summaryrefslogtreecommitdiffabout
path: root/gammu/emb/common/device/serial
Side-by-side diff
Diffstat (limited to 'gammu/emb/common/device/serial') (more/less context) (ignore whitespace changes)
-rw-r--r--gammu/emb/common/device/serial/ser_djg.c399
-rw-r--r--gammu/emb/common/device/serial/ser_djg.h37
-rw-r--r--gammu/emb/common/device/serial/ser_unx.c27
-rw-r--r--gammu/emb/common/device/serial/ser_w32.c9
4 files changed, 447 insertions, 25 deletions
diff --git a/gammu/emb/common/device/serial/ser_djg.c b/gammu/emb/common/device/serial/ser_djg.c
index 2524187..609deb8 100644
--- a/gammu/emb/common/device/serial/ser_djg.c
+++ b/gammu/emb/common/device/serial/ser_djg.c
@@ -1,3 +1,8 @@
+/* Some sources from SVAsync (c) 1996, 1997, Samuel Vincent
+ * 7337 Carioca Ct, Rohnert Park, Ca 94928
+ * "you may freely use it in your programs without paying me anything"
+ */
+/* Some sources from DZCOMM */
#include "../../gsmstate.h"
@@ -5,55 +10,419 @@
#ifdef DJGPP
#include "../../gsmcomon.h"
+#include "../../misc/coding/coding.h"
#include "ser_djg.h"
+#include <stdlib.h>
+#include <stdio.h>
+#include <string.h>
+#include <dos.h>
+#include <dpmi.h>
+#include <pc.h>
+#include <go32.h>
+#include <sys/farptr.h>
+#include <sys/movedata.h>
+#include <conio.h>
+
+extern unsigned short __djgpp_ds_alias;
+extern void SVAsyncProtISR(void);
+
+static unsigned char SVAsyncStatus=0;
+
+static void lock_interrupt_memory(void);
+static void unlock_interrupt_memory(void);
+
+#define Ctrl8259_0 0x020 /* 8259 port */
+#define Ctrl8259_1 0x021 /* 8259 port (Masks) */
+#define BufSize 32768 /* Buffer Size */
+
+static unsigned char VectorNum; /* Vector Number */
+static unsigned char EnableIRQ; /* Mask to enable 8259 IRQ */
+static unsigned char DisableIRQ; /* Mask to disable 8259 IRQ */
+static _go32_dpmi_seginfo ProtVector; /* Old Protmode Vector */
+static _go32_dpmi_seginfo info; /* New Protmode Vector */
+
+/* Register Addresses for the UART */
+static unsigned short Port; /* Port Base Address */
+unsigned short THR; /* Transmitter Holding Register */
+unsigned short RDR; /* Reciever Data Register */
+unsigned short BRDL; /* Baud Rate Divisor, Low byte */
+unsigned short BRDH; /* Baud Rate Divisor, High Byte */
+unsigned short IER; /* Interupt Enable Register */
+unsigned short IIR; /* Interupt Identification Register */
+unsigned short FCR; /* FIFO Control Register */
+unsigned short LCR; /* Line Control Register */
+unsigned short MCR; /* Modem Control Register */
+unsigned short LSR; /* Line Status Register */
+unsigned short MSR; /* Modem Status Register */
+unsigned short SCR; /* SCR Register */
+
+/* Data Buffer */
+unsigned volatile char RecBuffer[BufSize] = { 0 };
+unsigned volatile int RecHead, RecTail;
+
+/* This uninstalls the ISR and resets the serial port. */
+static void SVAsyncStop(void)
+{
+ if(!SVAsyncStatus) return;
+ SVAsyncStatus = 0;
+
+ /***** Mask (disable) 8259 IRQ Interrupt */
+ outportb(Ctrl8259_1, (inportb(Ctrl8259_1) | DisableIRQ));
+
+ /***** Disable 8250 interrupt */
+ outportb(LCR, (inportb(LCR) & 0x7F));
+ outportb(IER, 0);
+
+ /***** Set bit 3 in MCR to 0 */
+ outportb(MCR, (inportb(MCR) & 0xF7));
+
+ /***** Interrupts are disabled. Restore saved interrupt vector. */
+ _go32_dpmi_set_protected_mode_interrupt_vector(VectorNum, &ProtVector);
+}
+
+/* This will empty the receive buffer */
+static void SVAsyncClear(void)
+{
+ disable();
+ RecHead = 0;
+ RecTail = 0;
+ enable();
+}
+
+
+/* Sets communication parameters
+ * Baud = 150, 300, 600, 1200, 2400, 4800, 9600, 19200, 28800, 38400, 57600
+ * Control = The value to place in the LCR
+ */
+void SVAsyncSet(unsigned int Baud, unsigned int Control)
+{
+ int divisor;
+ unsigned char divlow, divhigh;
+
+ if (!Baud) return;
+
+ divisor = 115200 / Baud;
+
+ disable();
+
+ outportb(LCR, Control | 0x80); /* Set Port Toggle to BRDL/BRDH registers */
+ divlow = divisor & 0x000000ff;
+ divhigh = (divisor >> 8) & 0x000000ff;
+ outportb(BRDL, divlow); /* Set Baud Rate */
+ outportb(BRDH, divhigh);
+
+ outportb(LCR, Control & 0x007F); /* Set LCR and Port Toggle */
+
+ enable();
+}
+
+/* Sets various handshaking lines */
+void SVAsyncHand(unsigned int Hand)
+{
+ outportb(MCR, Hand | 0x08); /* Keep interrupt enable ON */
+}
+
+static void lock_interrupt_memory(void)
+{
+ int errval;
+ __dpmi_meminfo info;
+ unsigned long address;
+
+ __dpmi_get_segment_base_address(_my_ds(), &address);
+
+ info.address = (int) address + (int) &RDR;
+ info.size = sizeof(RDR);
+ errval = __dpmi_lock_linear_region(&info);
+ if(errval == -1) printf("Error in locking memory\n!");
+
+ info.address = (int) address + (int) &LSR;
+ info.size = sizeof(LSR);
+ errval = __dpmi_lock_linear_region(&info);
+ if(errval == -1) printf("Error in locking memory\n!");
+
+ info.address = (int) address + (int) &RecHead;
+ info.size = sizeof(RecHead);
+ errval = __dpmi_lock_linear_region(&info);
+ if(errval == -1) printf("Error in locking memory\n!");
+
+ info.address = (int) address + (int) &RecBuffer;
+ info.size = sizeof(RecBuffer);
+ errval = __dpmi_lock_linear_region(&info);
+ if(errval == -1) printf("Error in locking memory\n!");
+
+ info.address = (int) address + (int) RecBuffer;
+ info.size = BufSize;
+ errval = __dpmi_lock_linear_region(&info);
+ if(errval == -1) printf("Error in locking memory\n!");
+
+ __dpmi_get_segment_base_address(_my_cs(), &address);
+
+ info.address = (int) address + (int) SVAsyncProtISR;
+ info.size = 4096; /* 4096 bytes is probably overkill. */
+ errval = __dpmi_lock_linear_region(&info);
+ if(errval == -1) printf("Error in locking memory\n!");
+}
+
+static void unlock_interrupt_memory(void)
+{
+ __dpmi_meminfo info;
+ unsigned long address;
+
+ __dpmi_get_segment_base_address(_my_ds(), &address);
+ info.address = (int) address + (int) &RDR;
+ info.size = sizeof(RDR);
+ __dpmi_unlock_linear_region(&info);
+ info.address = (int) address + (int) &LSR;
+ info.size = sizeof(LSR);
+ __dpmi_unlock_linear_region(&info);
+ info.address = (int) address + (int) &RecHead;
+ info.size = sizeof(RecHead);
+ __dpmi_unlock_linear_region(&info);
+ info.address = (int) address + (int) &RecBuffer;
+ info.size = sizeof(RecBuffer);
+ __dpmi_unlock_linear_region(&info);
+ info.address = (int) address + (int) RecBuffer;
+ info.size = BufSize;
+ __dpmi_unlock_linear_region(&info);
+
+ __dpmi_get_segment_base_address(_my_cs(), &address);
+
+ info.address = (int) address + (int) SVAsyncProtISR;
+ info.size = 4096; /* probably overkill */
+ __dpmi_unlock_linear_region(&info);
+}
+
static GSM_Error serial_close(GSM_StateMachine *s)
{
- GSM_Device_SerialData *d = &s->Device.Data.Serial;
+ SVAsyncStop();
- return ERR_NOTIMPLEMENTED;
+ return ERR_NONE;
}
static GSM_Error serial_open (GSM_StateMachine *s)
{
- GSM_Device_SerialData *d = &s->Device.Data.Serial;
-
- return ERR_NOTIMPLEMENTED;
+ GSM_Device_SerialData *d = &s->Device.Data.Serial;
+ unsigned char temp;
+ int i;
+
+ /**** Set various things according to com port number */
+ if (mystrncasecmp(s->CurrentConfig->Device,"com1:",0)) {
+ Port = 0x03F8;
+ VectorNum = 0x0C;
+ EnableIRQ = 0xEF;
+ DisableIRQ = 0x10;
+ } else if (mystrncasecmp(s->CurrentConfig->Device,"com2:",0)) {
+ Port = 0x02F8;
+ VectorNum = 0x0B;
+ EnableIRQ = 0xF7;
+ DisableIRQ = 0x08;
+ } else if (mystrncasecmp(s->CurrentConfig->Device,"com3:",0)) {
+ Port = 0x03E8;
+ VectorNum = 0x0C;
+ EnableIRQ = 0xEF;
+ DisableIRQ = 0x10;
+ } else if (mystrncasecmp(s->CurrentConfig->Device,"com4:",0)) {
+ Port = 0x02E8;
+ VectorNum = 0x0B;
+ EnableIRQ = 0xF7;
+ DisableIRQ = 0x08;
+ } else return ERR_NOTSUPPORTED;
+
+ /**** Compute Register locations */
+ THR = Port;
+ RDR = Port;
+ BRDL = Port;
+ BRDH = 1 + Port;
+ IER = 1 + Port;
+ IIR = 2 + Port;
+ FCR = 2 + Port;
+ LCR = 3 + Port;
+ MCR = 4 + Port;
+ LSR = 5 + Port;
+ MSR = 6 + Port;
+ SCR = 7 + Port;
+
+ /***** Initalize Buffer */
+ SVAsyncClear();
+
+ lock_interrupt_memory();
+ atexit(unlock_interrupt_memory);
+ /***** Set bit 3 in MCR to 0 */
+ outportb(MCR, (inportb(MCR) & 0xF7));
+
+ /*** Save and reassign interrupt vectors */
+
+ _go32_dpmi_get_protected_mode_interrupt_vector(VectorNum, &ProtVector);
+
+ info.pm_offset = (int) SVAsyncProtISR;
+ info.pm_selector = _my_cs();
+ _go32_dpmi_set_protected_mode_interrupt_vector(VectorNum, &info);
+
+ atexit(SVAsyncStop);
+
+ /***** Enable 8259 interrupt (IRQ) line for this async adapter */
+ outportb(Ctrl8259_1, (inportb(Ctrl8259_1) & EnableIRQ));
+
+ /***** Enable 8250 Interrupt-on-data-ready */
+ outportb(LCR, (inportb(LCR) & 0x7F));
+
+ outportb(IER, 0);
+ if (inportb(IER)) {
+ SVAsyncStatus = 0;
+ return ERR_UNKNOWN;
+ }
+ outportb(IER, 0x01);
+
+ /***** Clear 8250 Status and data registers */
+ do {
+ temp=inportb(RDR);
+ temp=inportb(LSR);
+ temp=inportb(MSR);
+ temp=inportb(IIR);
+ } while(!(temp & 1));
+
+ /***** Set Bit 3 of MCR -- Enable interupts */
+ outportb(MCR, (inportb(MCR) | 0x08));
+
+ SVAsyncStatus = 1;
+ /***** Clear Buffer Just in case */
+ SVAsyncClear();
+
+ /* Code based on stuff from SVAsync lib.
+ * Clear UART Status and data registers
+ * setting up FIFO if possible
+ */
+ outportb(SCR, 0x55);
+ if (inportb(SCR) == 0x55) {
+ /* On the off chance that SCR is actually hardwired to 0x55,
+ * do the same check with a different value.
+ */
+ outportb(SCR, 0xAA);
+ if (inportb(SCR) == 0xAA) {
+ /* The chip is better than an 8250 - it has a scratch pad */
+ outportb(SCR, i); /* Set SCR back to what it was before */
+ inportb(SCR); /* Give slow motherboards a chance */
+
+ /* Is there a FIFO ? - go through twice for slow motherboards */
+ outportb(FCR, 0x01);
+ i = inportb(FCR);
+ outportb(FCR, 0x01);
+ i = inportb(FCR);
+
+ /* Some old stuff relies on this (no idea why) */
+ outportb(FCR, 0x00);
+ inportb(FCR); /* Give slow motherboards a chance */
+
+ if ((i&0x80) == 0) {
+ smprintf(s,"UART 16450 or UART 8250 with scratch pad\n");
+ } else if ((i&0x40) == 0) {
+ smprintf(s,"UART 16550 - broken FIFO\n");
+ } else {
+ /* It's a 16450A series : try and start the FIFO.
+ * It appears that some chips need a two call protocol, but
+ * those that don't seem to work even if you do start it
+ * twice. The first call is simply to start it, the second
+ * starts it and sets an 8 byte FIFO trigger level.
+ */
+ outportb(FCR, 0x01);
+ inportb(FCR); /* Give slow motherboards a chance */
+ outportb(FCR, 0x87);
+ inportb(FCR); /* Give slow motherboards a chance */
+
+ /* Check that the FIFO initialised */
+ if ((inportb(IIR) & 0xc0) != 0xc0) {
+ /*
+ * It didn't so we assume it isn't there but disable it to
+ * be on the safe side.
+ */
+ outportb(IIR, 0xfe);
+ inportb(IIR); /* Give slow motherboards a chance */
+ smprintf(s,"UART 16450A - FIFO disabled\n");
+ } else {
+ smprintf(s,"UART 16450A - FIFO enabled\n");
+ }
+ }
+ } else {
+ smprintf(s,"UART 8250\n");
+ }
+ }
+
+ d->Control = BITS_8 | STOP_1;
+ d->Parity = false;
+ d->Speed = 9600;
+ SVAsyncSet(d->Speed,d->Control | NO_PARITY);
+
+ return ERR_NONE;
}
static GSM_Error serial_setparity(GSM_StateMachine *s, bool parity)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
- return ERR_NOTIMPLEMENTED;
+ d->Parity = parity;
+
+ if (parity) {
+ SVAsyncSet(d->Speed, d->Control | ODD_PARITY);
+ } else {
+ SVAsyncSet(d->Speed, d->Control | NO_PARITY);
+ }
+
+ return ERR_NONE;
}
static GSM_Error serial_setdtrrts(GSM_StateMachine *s, bool dtr, bool rts)
{
- GSM_Device_SerialData *d = &s->Device.Data.Serial;
+ if (dtr && rts) {
+ SVAsyncHand(DTR | RTS);
+ } else if (dtr) {
+ SVAsyncHand(DTR);
+ } else if (rts) {
+ SVAsyncHand(RTS);
+ } else {
+ SVAsyncHand(0);
+ }
- return ERR_NOTIMPLEMENTED;
+ return ERR_NONE;
}
static GSM_Error serial_setspeed(GSM_StateMachine *s, int speed)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
- return ERR_NOTIMPLEMENTED;
+ d->Speed = speed;
+
+ if (d->Parity) {
+ SVAsyncSet(d->Speed, d->Control | ODD_PARITY);
+ } else {
+ SVAsyncSet(d->Speed, d->Control | NO_PARITY);
+ }
+
+ return ERR_NONE;
}
-static int serial_read(GSM_StateMachine *s, void *buf, size_t nbytes)
+static int serial_read(GSM_StateMachine *s, char *buf, size_t nbytes)
{
- GSM_Device_SerialData *d = &s->Device.Data.Serial;
+ if(RecTail == RecHead) return 0;
+
+ disable();
+ buf[0] = RecBuffer[RecTail++];
+ if(RecTail >= BufSize) RecTail = 0;
+ enable();
- return 0;
+ return 1;
}
-static int serial_write(GSM_StateMachine *s, void *buf, size_t nbytes)
+static int serial_write(GSM_StateMachine *s, char *buf, size_t nbytes)
{
- GSM_Device_SerialData *d = &s->Device.Data.Serial;
+ int i;
+
+ for (i=0;i<nbytes;i++) {
+ while(~inportb(LSR) & 0x20);
+ outportb(THR, buf[i]);
+ }
- return 0;
+ return i;
}
GSM_Device_Functions SerialDevice = {
diff --git a/gammu/emb/common/device/serial/ser_djg.h b/gammu/emb/common/device/serial/ser_djg.h
index b35b282..3bb2a5b 100644
--- a/gammu/emb/common/device/serial/ser_djg.h
+++ b/gammu/emb/common/device/serial/ser_djg.h
@@ -1,12 +1,47 @@
+/* Some sources from SVAsync (c) 1996, 1997, Samuel Vincent
+ * 7337 Carioca Ct, Rohnert Park, Ca 94928
+ * "you may freely use it in your programs without paying me anything"
+ */
#ifdef DJGPP
#ifndef djgppserial_h
#define djgppserial_h
typedef struct {
- int hPhone;
+ int hPhone;
+ int Speed;
+ unsigned int Control;
+ bool Parity;
} GSM_Device_SerialData;
+/* Defines for Com Port Paramaters, the second paramater to SVAsyncSet() */
+#define BITS_8 0x03
+#define BITS_7 0x02
+#define STOP_1 0x00
+#define STOP_2 0x04
+#define EVEN_PARITY 0x18
+#define ODD_PARITY 0x08
+#define NO_PARITY 0x00
+
+/* Defines for SVAsyncHand() */
+#define DTR 0x01
+#define RTS 0x02
+#define USER 0x04
+#define LOOPBACK 0x10
+
+/* Defines for SVAsyncStat() */
+#define D_CTS 0x0100
+#define D_DSR 0x0200
+#define D_RI 0x0400
+#define D_DCD 0x0800
+#define CTS 0x1000
+#define DSR 0x2000
+#define RI 0x4000
+#define DCD 0x8000
+#define PARITY 0x0004
+#define THREMPTY 0x0020
+#define BREAKDET 0x1000
+
#endif
#endif
diff --git a/gammu/emb/common/device/serial/ser_unx.c b/gammu/emb/common/device/serial/ser_unx.c
index 69c7515..18b5f6f 100644
--- a/gammu/emb/common/device/serial/ser_unx.c
+++ b/gammu/emb/common/device/serial/ser_unx.c
@@ -4,6 +4,15 @@
* (C) 1999-2000 Hugh Blemings & Pavel Janik ml. (C) 2001-2004 Pawel Kot
* GNU GPL version 2 or later
*/
+/* Due to a problem in the source code management, the names of some of
+ * the authors have unfortunately been lost. We do not mean to belittle
+ * their efforts and hope they will contact us to see their names
+ * properly added to the Copyright notice above.
+ * Having published their contributions under the terms of the GNU
+ * General Public License (GPL) [version 2], the Copyright of these
+ * authors will remain respected by adhering to the license they chose
+ * to publish their code under.
+ */
#include "../../gsmstate.h"
@@ -60,8 +69,8 @@ static GSM_Error serial_close(GSM_StateMachine *s)
static GSM_Error serial_open (GSM_StateMachine *s)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
- struct termios t;
- int i;
+ struct termios t;
+ int i;
/* O_NONBLOCK MUST is required to avoid waiting for DCD */
d->hPhone = open(s->CurrentConfig->Device, O_RDWR | O_NOCTTY | O_NONBLOCK);
@@ -124,7 +133,7 @@ static GSM_Error serial_open (GSM_StateMachine *s)
static GSM_Error serial_setparity(GSM_StateMachine *s, bool parity)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
- struct termios t;
+ struct termios t;
if (tcgetattr(d->hPhone, &t)) {
GSM_OSErrorInfo(s,"tcgetattr in serial_setparity");
@@ -150,8 +159,8 @@ static GSM_Error serial_setparity(GSM_StateMachine *s, bool parity)
static GSM_Error serial_setdtrrts(GSM_StateMachine *s, bool dtr, bool rts)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
- struct termios t;
- unsigned int flags;
+ struct termios t;
+ unsigned int flags;
if (tcgetattr(d->hPhone, &t)) {
GSM_OSErrorInfo(s,"tcgetattr in serial_setdtrrts");
@@ -264,8 +273,8 @@ static int serial_read(GSM_StateMachine *s, void *buf, size_t nbytes)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
struct timeval timeout2;
- fd_set readfds;
- int actual = 0;
+ fd_set readfds;
+ int actual = 0;
FD_ZERO(&readfds);
FD_SET(d->hPhone, &readfds);
@@ -283,8 +292,8 @@ static int serial_read(GSM_StateMachine *s, void *buf, size_t nbytes)
static int serial_write(GSM_StateMachine *s, void *buf, size_t nbytes)
{
GSM_Device_SerialData *d = &s->Device.Data.Serial;
- int ret;
- size_t actual = 0;
+ int ret;
+ size_t actual = 0;
do {
ret = write(d->hPhone, (unsigned char *)buf, nbytes - actual);
diff --git a/gammu/emb/common/device/serial/ser_w32.c b/gammu/emb/common/device/serial/ser_w32.c
index 7d88fc7..a7919fe 100644
--- a/gammu/emb/common/device/serial/ser_w32.c
+++ b/gammu/emb/common/device/serial/ser_w32.c
@@ -4,6 +4,15 @@
* (C) 1999-2000 Hugh Blemings & Pavel Janik ml. (C) 2001-2004 Pawel Kot
* GNU GPL version 2 or later
*/
+/* Due to a problem in the source code management, the names of some of
+ * the authors have unfortunately been lost. We do not mean to belittle
+ * their efforts and hope they will contact us to see their names
+ * properly added to the Copyright notice above.
+ * Having published their contributions under the terms of the GNU
+ * General Public License (GPL) [version 2], the Copyright of these
+ * authors will remain respected by adhering to the license they chose
+ * to publish their code under.
+ */
#include "../../gsmstate.h"